Bike speed and climb time calculator
Turn watts into speed on the flat, on a climb or into a headwind, see your climb time and VAM, and find out whether more power, less weight or a better position buys you the most time.
1. You and your bike
Total mass is rider plus bike, bottles, shoes and kit. CdA is your drag area: how much air you push. Pick the position closest to how you will ride, or enter a measured CdA.
2. Speed and time from power
Use the steady power you expect to hold. For a race, that is your target race power, not your FTP.
Speed, time and what each change is worth
Steady speed
34.2 km/h
21.2 mph
Time for 90 km
2:38:03
Steady-state model: no corners, stops or surges.
Power-to-weight
2.50 W/kg
Rider weight only.
Aero efficiency
667 W/m²
Watts per CdA: the flat-course equivalent of W/kg.
Time saved over 90 km by one change
| Change | Time saved |
|---|---|
| 10 W more power | 3:17 |
| 2 kg less total mass | 0:20 |
| 0.02 m² lower CdA (a better position) | 3:40 |
| Rolling resistance 0.001 lower (faster tyres) | 2:38 |
Your speed at 180 W on other gradients
| Gradient | Speed | Time per km |
|---|---|---|
| -4% | 56.3 km/h | 1:04 |
| -2% | 45.7 km/h | 1:19 |
| 0% | 34.2 km/h | 1:45 |
| +2% | 23.5 km/h | 2:33 |
| +4% | 16.1 km/h | 3:44 |
| +6% | 11.7 km/h | 5:07 |
| +8% | 9.1 km/h | 6:34 |
| +10% | 7.5 km/h | 8:03 |
3. Climb time and VAM
Enter a climb from the course profile: its length and average gradient, and the power you plan to hold on it.
Climb estimate
Climb time
23:11
12.9 km/h average
VAM (vertical metres per hour)
775 m/h
299 m of climbing
Climbing power-to-weight
2.78 W/kg
On this climb
+10 W saves 1:01
1 kg less body weight saves 0:15
4. Power needed for a target flat speed
Uses the position, mass, surface, air and wind above, on a flat road.
Power needed
191 W
2.66 W/kg
Where to go next
Learn what the watts mean in cycling watts explained, how to measure your CdA in the aero testing guide, and when W/kg matters in the power-to-weight guide. Set your race power from a recent test with the FTP and power zone calculator, and check that your easiest gear lets you keep turning the pedals on the steepest climb with the gear ratio calculator.
One practical triathlon decision each week
A useful decision, tool, checklist, or evidence-backed update for your next training block or race.
No spam. Unsubscribe anytime.
Updated
What the bike speed and climb time calculator does
This calculator answers the questions triathletes most often work out by hand from a course profile and a power number: how fast will I ride at my race power, how long will this climb take, and what would actually make me faster? It uses a standard steady-state cycling model, the same physics behind most bike-split planning software, and shows every assumption so you can change it.
It has four parts:
- You and your bike: rider weight, bike and kit weight, riding position (drag area, CdA), tyres and road surface (rolling resistance, Crr), altitude and air temperature.
- Speed and time from power: your steady power, gradient, wind and distance give a speed, a bike split, your W/kg and your W/CdA, plus a table of what four common changes are worth.
- Climb time and VAM: the length and average gradient of a climb and your climbing power give a climb time, average speed and VAM (vertical metres per hour).
- Power for a target speed: the reverse question, on a flat road.
The physics behind the numbers
At a steady speed, the power reaching the rear wheel must equal the power lost to three resistances:
wheel power = speed × (gravity force + rolling resistance force + aerodynamic drag force)
- Gravity: total mass × 9.81 × sine of the road angle. Zero on the flat, large on climbs, negative (helping you) downhill.
- Rolling resistance: total mass × 9.81 × cosine of the road angle × Crr.
- Aerodynamic drag: ½ × air density × CdA × (your speed plus headwind)². Air density is calculated from your altitude and temperature: at sea level and 20 °C it is about 1.20 kg/m³, at 1,500 m and 25 °C about 0.99 kg/m³.
Power at the pedals is higher than power at the wheel because the chain and bearings lose a little. The calculator assumes 97.5% drivetrain efficiency, a typical figure for a clean, well-lubricated chain.
Because drag grows with the square of speed and the power to overcome it with roughly the cube, the calculator solves for speed numerically rather than with a simple formula. That is why doubling power never doubles speed on the flat.
Choosing realistic inputs
Rider and bike weight. Weigh yourself on the morning of a ride. For the bike, include two full bottles, shoes, helmet and saddle bag: a race-ready road or triathlon bike is usually 9–12 kg in total.
Position (CdA). The presets are typical values for each position: 0.40 m² upright on the tops, 0.32 on the hoods, 0.29 in the drops, 0.27 on a road bike with clip-on bars, 0.25 for a typical age-group triathlon bike fit and 0.22 for a tested, well-fitted long-course position. Real athletes vary a lot around these numbers. If you have measured your CdA, choose "I know my CdA"; our aero testing guide explains how to measure it for free with a power meter.
Tyres and surface (Crr). 0.004 represents fast race tyres on smooth tarmac, 0.005 good training tyres on normal roads and 0.007 rough chip-seal. Rolling resistance matters more than most people expect: on a flat 90 km bike, moving from 0.005 to 0.004 is worth a couple of minutes for many age-groupers.
Power. Enter the power you will actually hold, not your FTP. For a 70.3 that is commonly in the region of 75–85% of FTP and for a full distance about 65–78%, depending on fitness and experience; our cycling watts guide explains pacing targets.
Wind. Enter a positive number for a headwind and a negative number for a tailwind. A course with an out-and-back in the wind is always slower than a calm day, because the headwind leg costs more time than the tailwind leg gives back. You can check this by running the same distance at +15 km/h and at −15 km/h and averaging the two times.
Reading the results
Steady speed and time. This is what a perfectly steady rider would do on a uniform road. Real courses include corners, turnarounds, aid stations, traffic calming and changes of position, so expect a real split to be a few percent slower on a simple course and more on a technical one.
W/kg and W/CdA. Power-to-weight (W/kg) predicts climbing speed. Watts per CdA predicts flat-road speed. On a flat course, two riders with the same W/CdA ride at almost the same speed even if one produces far more power. Our power-to-weight guide explains when each matters.
"Time saved by one change." The calculator re-runs your ride four times with one thing changed: 10 W more power, 2 kg less mass, 0.02 m² less CdA and 0.001 less rolling resistance. This is the most useful output for deciding where to spend money and training time. On flat courses the CdA line usually wins; on steep climbs the mass and power lines catch up.
Gradient table. Your speed at the same power on gradients from −4% to +10%. It shows how speed collapses on steep climbs, which is normal, and why chasing speed rather than power on a climb wrecks your run.
VAM. Vertical metres climbed per hour. Well-trained age-groupers often see 700–1,000 m/h on long climbs at race effort; professional cyclists exceed 1,600 m/h. VAM is a handy way to compare climbs of different lengths and gradients.
Worked example: planning a 70.3 bike split
An athlete weighs 68 kg, rides a 9.5 kg road bike with clip-on bars (CdA 0.27), fast tyres (Crr 0.004) and plans to hold 170 W on a 90 km course at 300 m altitude on a 22 °C day.
- On the flat, the calculator gives roughly 34.5 km/h, a steady-state split of about 2:37.
- The course has one 4 km climb at 5%. At 200 W on that climb, it takes about 15 minutes at around 16 km/h, a VAM of about 800 m/h.
- The "time saved" table shows 0.02 m² less CdA is worth more than 2 kg less mass for this rider over the whole course, so a fit session and an aero helmet test come before buying lighter wheels.
Limits you should know
- The model is steady-state. It does not include acceleration out of corners, braking, drafting (illegal in most age-group races anyway) or changing your position on climbs.
- CdA changes with yaw angle in crosswinds and with fatigue. A position you test fresh may not be the one you hold at hour three.
- Wind on real courses is rarely a clean headwind or tailwind; it gusts and changes direction.
- Descents above about 50–60 km/h are limited by safety, corners and braking, not by physics. Never use a predicted descent speed as a target.
- The numbers are planning estimates. They are good for comparing choices and pacing a course, not for promising a finish time.
Where to go next
Turn your race power into training zones with the FTP and power zone calculator. If you are thinking about an aero upgrade, read aero testing for triathletes before you buy, and check clip-on aero bars for road bikes if you do not yet have an aero position. For hilly courses, the triathlon hill climbing guide shows how to turn your climb times into a pacing plan.
Understand the estimate, then act
Review the assumptions behind this planning aid before using the result, then continue to the most relevant practical step.